Repair
Jura repair in Aarhus
We repair Jura fully automatic coffee machines in our workshop in Tilst — from the ENA series to the larger GIGA and Impressa models.
Jura machines are known for their durability, but the brew unit, grinder and boiler wear down like on any other machine after years of daily use. We know our way around Jura's internals and can usually take the machine apart and put it back together without anything breaking along the way.
Models we repair
- Jura E8
- Jura E8 EB
- Jura E80
- Jura ENA 4
- Jura ENA 8
- Jura ENA 8 EB
- Jura ENA Micro 90
- Jura GIGA X3 Professional
- Jura GIGA X8 Professional
- Jura J8
- Jura S8
- Jura WE8
- Jura X6
- Jura XJ9 Professional
- Jura Z6
- Jura Z8
Common faults on Jura machines
- Jura E8 — Fill beans / no beans
- Jura E8 — Internal water leak
- Jura E8 EB — Coffee/water ends up in drip tray
- Jura E80 — Service / weak-inconsistent brew
- Jura ENA 4 — No water / airlock / tray warning
- Jura ENA 8 — No coffee or hot water; water goes to tray
What should you bring?
- The machine itself, ideally with the water tank emptied
- The power cable
- A short description of the problem — feel free to email us beforehand
Real Jura repairs
See the full portfolio
Jura Impressa J5
Problem: Machine started descaling but stopped halfway and showed E8 error. Coffee tasted bitter and weak.
Solution: Scale sensors cleaned, descaling program completed manually. Brew unit fitted with new seal.
Jura W10
Problem: A water leak at an internal connection.
Solution: A T-piece and a hose were replaced.
Jura Z6
Problem: The grinder wasn't working correctly.
Solution: The grinder was rebuilt and adjusted.
Jura ENA 8
Problem: A damaged brew group on one machine and a faulty grinder on another.
Solution: The brew group was repaired/rebuilt, and on another ENA 8 the grinder was replaced.
Jura E8
Problem: Leaks, coffee in the drip tray, a 'no beans' fault, and wear in the brew group.
Solution: The brew group was rebuilt with a service kit, connections/hoses were repaired, and on another unit the grinder was diagnosed/replaced.
Jura S8
Problem: A leak during brewing and a need for major service.
Solution: A damaged 90° connector, hose clamp and brew group parts were serviced/replaced.
Jura Z8
Problem: Coffee partly ending up in the drip tray, and on another unit conflicting water/drip-tray faults.
Solution: The brew group was identified as the fault area on one machine; sensors and connections were diagnosed on another.
Jura ENA 4
Problem: No water passing through the machine.
Solution: The brew group was disassembled, cleaned and rebuilt, followed by descaling and filter service.
Jura E80
Problem: The machine needed service on both the brew group and grinder.
Solution: The brew group and grinder were rebuilt and serviced.
Jura X6
Problem: The machine couldn't draw in water.
Solution: The water circuit and brew group were reviewed and serviced with a premium rebuild kit.
Jura XJ9 Professional
Problem: A leak around the water tank/water supply.
Solution: The tank connection and relevant seals/connections were repaired.
Jura GIGA X8 Professional
Problem: The machine kept asking to fill the system and had flow issues.
Solution: The machine was descaled and the water circuit serviced, with focus on flowmeters, membranes and the brew group.
Jura GIGA X3 Professional
Problem: Water ended up in the drip tray and brewing was unstable.
Solution: The outlet valves and pump membrane were replaced, the flowmeter cleaned, and the brew group rebuilt.
Jura J8
Problem: Espresso-based drinks were interrupted and the machine made an unusual noise during rinsing.
Solution: The fault was traced to a damaged brew group, which was serviced/refurbished.
Jura ENA 3
Problem: The machine got stuck in an 'open/close valve' loop.
Solution: The pump, flowmeter, membrane and valve mechanism were systematically tested; the control board was suspected as the remaining fault.
Jura ENA Micro 9 Aroma+
Problem: A worn/damaged brew group, grinder and ceramic valve across different units.
Solution: The brew group was rebuilt on a refurbishment unit, while other parts were diagnosed and assessed for replacement.
Jura E60
Problem: The machine needed a rebuild of the grinder and water/brew system.
Solution: The grinder, O-rings, filter and other service components were reviewed as part of a full refurbishment.
Jura Cool Control 591
Problem: The unit was missing its lid/power accessory.
Solution: The missing parts were identified, and the unit was worked on as a refurbishment project.
Jura ENA 8 EB
See the caseIs your Jura machine broken?
Contact us today for a non-binding quote. Diagnostics cost 400 kr. and are deducted from the repair price if you go ahead.